Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround
Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround
Blog Article
This article below relating to A Step-by-Step Guide to Installing a Bathtub is immensely engaging. Have a go and draw your own personal ideas.
Installing a tub isn't precisely rocket science, however it does require strong plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is additionally a moderately difficult task. If the old tub is readily easily accessible, the project can relocate rapidly; if you have to open up a wall to remove the old bathtub and place the new tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly need a helper to move out the old tub and also set in the new one. See to it you have qualified on your own for the job and also are comfortable attempting it. As opposed to employing a service provider to take over a halfway-completed project, it is far better to consider using one before you start. Possibilities are you may require a professional plumber to make tube links.
This post will assist you install a new bath tub in your shower room if you have currently bought a brand-new tub and also don't require to change the setup of your previous supply of water pipelines.
Your devices and product checklist must comprise the following:
Getting ready for the Installation
First of all, the sustaining frame provided with the bath ought to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the tap includes a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets device to prevent stress on the bath tub.
Fit the flexible tap adapters to the bottom of the two taps utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you use all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its last placement.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the water supply. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be fairly problematic due to the restricted gain access to that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the remaining water that will originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipe connections on the old taps to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Installing the Tub
Making use of both wooden boards under its feet, place the bathtub in the called for placement. The wood boards are handy in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 tiny factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be attained by examining the level as well as changing the feet on the bathtub till the level checks out level.
To install faucets, fit all-time low of the outermost versatile tap connector to the ideal supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Turn on the supply of water and examine all joints and also brand-new pipework for leaks and tighten them if essential. Fill up the tub and additionally inspect the overflow outlet and the regular electrical outlet for leaks.
Finally, deal with the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the bath tub must wait until the bath tub has actually been used at the very least once as this will resolve it into its last setting.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making sure that the washers remain in place in between the tap and also the sink. Secure the faucet in place with the maker provided backnut. As soon as the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular tap adapters. The former kind should be linked to the tap ends first, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bath satisfies the tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to break an inflexible seal, causing the water to permeate the wall surface between the bath and also the tiling, leading to issues with wetness and possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes as well as cartridges, as well as can sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill up the tub with water prior to securing, to allow for the movement experienced when the tub remains in usage. The sealer can crack fairly very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently available on the market. It is advisable to fit the ceramic tiles utilizing waterproof or water resistant glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was introduced to that article on How to Install a Bathtub through an associate on another domain. Are you aware of another person who is fascinated by the niche? Take a moment to share it. I recognize the value of reading our article about How to Install a Bathtub.
This Post
Report this page